220 V dual tajmer infinity loop vremenski relej

Karakteristike:  

Pomoću funkcije pokretanja / zaustavljanja, nakon pokretanja modula u režimu beskonačne petlje, relej radi u skladu sa zadanim vremenom. To je vremenski relej modul visoke preciznosti, stabilne i pouzdane performanse. Postoji širok vremenski raspon koji možete podesiti, i „ RUN“ i „ STOP“ vreme su podesiva. Podržava funkciju pokretanja/zaustavljanja, modul ulazi u režim beskonačnog ciklusa nakon uključivanja, relej radi u skladu sa radnim vremenom i vremenom zaustavljanja.  

Specifikacije:  

Radni model: pritisnite dugme za pokretanje ciklusa, a zatim pritisnite dugme za pokretanje da biste prestali sa radom.  
Pokrenite režim ciklusa: Uključeno - Isključeno - Uključeno - Isključeno - - 
Napon: AC 100V-250V, može se koristiti za napajanje 100V / 110V / 120V / 127V / 220V / 230V / 240V.  
Potrošnja energije: <1.0V 
Izlaz: Aktivni izlaz, izlazni napon jednak je ulaznom naponu.  
Maks. Izlazna struja: <10A 
Ulaz: ulaz pasivnog prekidača, zeleno led svetli posle uključivanja, crveno led svetli posle zaustavljanja Vremenski opseg: 0,5 sekundi -1000 minuta 
Vremenska tačnost: Mak. vrednost opsega * 0,001 (rezolucija 1000).  
Ulaz (dugme za start): ulaz pasivnog prekidača, zeleno led svetli posle uključivanja, crveno led svetli posle zaustavljanja - pokretanje ulaza nije neophodno.  
Možete da povežete dva terminala 2 terminala kratkom žicom, a zatim će ploča kružiti beskonačno petlju (bez tastera) nakon uključivanja.  
Život: 100 hiljada puta 
Veličina: 88X38X22 mm
Razmak rupe za ugradnju: 83X33mm
Prečnik montažne rupe: 3,2 mm

Terminal: < --L power L line (fireWire) input < --N power N line (zero line) input --> Ouput N, load N line --> Ouput: L1, load L line most appliances do not need to strictly distinguish the LN line --> LNC L line output normally closed, generally do not connect.

Operating instructions:  
Time can be set when the board is powered on or powered off.  
1. Set Run Time (ON time setting):   RUN TIME under the identification of the potentiometer adjustment time, clockwise for the increase in length, counterclockwise to shorten the length of time.   The red switch below can set time range(left, 0-100 or 0-1000) and unit(right, Sec. or Min. ) Potentiometer allocated code switch set to the left time range. The adjustable range of the adjustable resistor is 0-100; the dial range is 0-1000. The potentiometer allocated code switch unit set right. Dial down to Sec. indicating unit for seconds; dial up to Min. to indicate unit for minute.  
2. Set Stop Time ( OFF time setting ):   OFF TIME under the identification of the potentiometer adjustment time, clockwise for the increase in length, counterclockwise to shorten the length of time. Adjust the STOP TIME potentiometer clockwise to increase, counterclockwise to decrease.   The red switch below can set time range(left, 0-100 or 0-1000) and unit(right, Sec. or Min. ) Potentiometer allocated code switch set to the left time range. The adjustable range of the adjustable resistor is 0-100; the dial range is 0-1000. The potentiometer allocated code switch unit set right. Dial down to Sec. indicating unit for seconds; dial up to Min. to indicate unit for minute.  
3. Start Button(Not included): Connect a momentary push-button switch and press it, then green LED lights up indicating it is working. The board would automatically run according to the setting run time and stop time, infinite cycle. Press the start button again, then red LED lights up indicating it stops. Access to the reset button, click, switch to the green light, indicating that the running state, the module will automatically set in accordance with the running time and the length of time to stop working, infinite loop. Click the start button again, the module will switch to red light, said to be in a stopped state.  
4. Time Setting Example: Requirement: Run for 20 seconds, stop for 30 minutes, infinite loop cycle ( connect 20 seconds, disconnect 30 minutes ). Settings Up: (1)Set run time range down to 0-100; (2)Set run time unit down to Sec. ; (3)Set run time potentiometer to 20 position, namely the position of 20/100 from left;  

******************************************************
UŠTEDITE VREME NARUČITE ZA 30 SEKUNDI 
Pošaljite SMS na broj telefona  063/174-1111 
******************************************************
Ime i prezime.   
Ulica i broj.   
Mesto i poštanski broj.   
Broj telefona za kontakt.   
Naručujem  A382K64  220 V dual tajmer infinity loop
*******************************************************