PLC kontroler FX1N-32MR, 16 ulaza, 16 izlaza, 24V

PLC kontroler FX1N-32MR, 16 ulaza, 16 izlaza, 24V - 

Programabilni Logički Kontroler

Karakteristike:

Model FX1N-32MR
Napajanje: DC 24V, 3W
Ulazi: 16 PNP
Izlazi: 16 RELE
Programski jezici: Ladder diagram, SFC stepping instructions
Podržane aplikacije: GX-Develoer, GX-WORK2
Podržano programiranje, monitoring, download
Memorija: 8K step EEPROM
Dimenzije: 120 x 110 x 60 mm
Montaža na DIN šinu

PLC Industrial Control Board DC24V FX1N 32MR DC24V 6W 16 Input 16 Output Baud Rate 9600 Support HMI

 Product function description
1. Write application in ladder language, support GX-Develoer, GX-WORK2
2. Support human-machine interface connection, the application is completely equivalent to FX1N.
3. Support ladder programming, download, monitor.
4. The programming port is the port for downloading and communicating with the man-machine interface.
5. This PLC adopts industrial-grade 32-bit MCU with strong anti-interference, and its running speed far exceeds the original FX1N.
6. The company's original password protection, as long as the password is 12345678 internal programs are protected, to prevent your program from being illegally stolen, to protect your labor results. If the password is set to 12345678 and there is no program reading function, you can only download the program and the "parameter" option cannot be checked when downloading. Unable to unlock password! !

Note
1. The board is powered by DC 24V. Do not input AC or 220V.
2. The board uses the serial port to download the program. If the computer does not have a serial port, please purchase the USB to serial cable.

This PLC transmission baud rate is 9600 as shown below

Product Resource Description
1. Board 16 points output 16 points input (16 relay outputs).
2. The board is powered by DC 24V. Do not input AC or 220V voltage.
3. The internal resources of the board are allocated as follows.
 
project - performance
Operation control method - Stored program repeatedly scanning mode
Input and output control mode - Batch mode (when executing END instruction), input and output refresh command, pulse capture function
Programming language - Ladder diagram, SFC stepping instructions
Ladder programming software - GX Developer, GX Works2
Program memory - 8K step EEPROM
Type of instruction
Direct instruction - 27
Step ladder instruction - 2
Basic application instruction - 70
Instructions speed
Basic instructions - 0.1μ S-0.55μ S instruction
Application instructions - 0.8μ S-10μ S instruction
input Output
Input relay X - X0-X127,128 points
Output relay Y - Y0-Y127,128 poinst
Auxiliary relay M
General use - M0-M1523,1524 points
Special use - M8000-M1535,1152 points( after M500 Power down save)
State S - S10-S999,1000 points
Timer T
100MS - T0-199,200 points
10MS - T200-T245,46 points
1MS - T246-T249,4 points
100MS accumulation - T250-T255,6 points
Counter C
Counter 16 bits - C0-C199,200point(after C100 Power down save)
Counter 32 bits - C200-C255,56 points
Data register
General use - D0-D500(after D200 Power down save),500point
Special use - D8000-D8255,255 points
Indexing - V7-V0, Z7-Z0,16 points
Nested pointer - P0-P127,128 points
constant
K 16 bit - -32768-32767
K 32 bit - -2 147 483 648-2 147 483 647
H 16 bit - 0-FFFF
H 32 bit - 0-FFFFFFFF

Support instruction set - 27 basic instructions

Mnemonic, name, function, Available Soft Components
[LD] take, Operation start“ a” contact, XYMSTC
[LD] take reverse, Operation start“ b” contact, XYMSTC
[LDP] take pulse rising edge, The rising edge detects the start of the operation, XYMSTC
[LDF] take the pulse falling edge, The falling edge detects the start of the operation, XYMSTC