Nov Set za reparaciju vetrobranskog stakla mod 5 sofersajbna

060-355-0-325 Brzo i lako zalepite i otklonite ostecenje na sofersajni.  

Izuzetno jak lepak za staklo, prodire u svakupukotinu, sanira pukotinu i obnavlja prozirnost stakla na tom mestu.  Veoma je jednostavan za upotrebu i daje odlicne rezultate.  Set za reparaciju vetrobrana, sanira ostecenja stakla nastala udarom kamenica ili slicnih predmeta.  

Nakon zavrsetka lepljenja, auto ostavite  na suncu, da pod dejstvom UV zraka lepak dodatno ocvrsne.  
Mozete koristiti i UV lampu da lepak brze ocvrsne  preporucujem Uv lampu iz mog oglasa 400din
Povrsinu koji tretirate, dobro isperite, ocistite od slobodnih krhotina stakla i osusite.  
lepljenja obavite na mestu gde ste zaklonjeni od direktnih suncevih zraka

Sam postupak mozete videti na Youtube   otkucajte    WINDSCREEN REPAIR KIT

Car Windshield Repair Tool DIY Car Window Repair Tools Window Glass Curing Glue Auto Glass Scratch Crack Restore Kit

Features:

The product pressure bar is provided with a sealing ring to form a closed pressurized space. 0.7cm diameter * 4cm height cavity, providing more pressure. The advantage of the new structure, with the function of vacuumizing, is to extract the air in the cracks. The risk of crushing glass in the process of pressurization is solved. For the stubborn crack damage, the repair effect is better. With more pressure, it can repair larger wounds, and the repair effect is better. The positioning bracket is provided with two positioning screw holes, which solves the defect that the edge of the early generation products is damaged and cannot be repaired. According to statistics, edge damage accounts for 60% of glass damage. By adding the spiral hole, the repair rate is greatly increased. Steps: 1. Clean the periphery of the broken glass mouth, and there shall be no stain and moisture inside the broken glass mouth 2. Find the glue injection port of the damaged part, and use the pick needle to remove the broken glass 3. Apply a few drops of repair resin on the surface of the damaged mouth to lubricate it 4. Align the center point of the positioning bracket circle with the damaged port, and press the suction cup to install firmly 5. Apply a few drops of repair resin to the silica gel head of the pressure cylinder for lubrication 6. Screw the pressure cylinder into the positioning bracket, tighten the glass tightly, and align the glue injection port with the damaged port 7. Hold the pressure cylinder, slowly screw out the pressure rod, and keep vacuumizing for about 10 minutes 8. Screw out and pull out the pressure rod, and drop 1-2 drops of repair liquid into the pressure cylinder 9. Insert the pressure bar again and screw it in slowly (if there is resistance, screw it in slightly after pressing down) 10. Keep pressurizing for 10 minutes, and observe the change of the damaged part. If there is no change, rotate it downward and a little bit 11. Go to the 45 ° angle in the car and observe whether the glass breaks and disappears, and the penetration is completed 12. Remove the suction cup pressurizing tool and proceed to the next step 13. Drop a drop of repair solution to the damaged mouth, and apply the curing film to scrape off the bubbles with the blade 14. Move the vehicle to direct sunlight for 10-30 minutes or replace it with ultraviolet lamp until it solidifies 15. Tear off the curing film and scrape off the excess resin 16. If there is residual fogging point, use fogging point curing film (circular film) for secondary curing 17. Drop as little liquid as possible at the fogging point, cover with curing film to naturally, and do not with the blade 18. UV curing, just tear off the curing film (do not use a knife to scrape)   The package includes: 1*Repair resin 5*Cure strips 1*blade 1* sucker or 1*Repair fluid 1*Pin picking 1* Cured film 1*Repair blade 4* Lift