slika
slika
slika
1 od 3

Darkglass Microtubes 500

93.240 din

Novo
Beograd
640
4
pre 5 dana
Odgovara na 98% poruka, uglavnom u roku od jednog dana.
Artistsystems online
Član od 16.08.2011.
Svi oglasi

Neverovatna ponuda na našem tržištu!
DarkGlass samo u AudioPro-Artist-u po NAJBOLJIM CENAMA!

Microtubes 500 je pojačalo od 500w opremljeno analognim "solid" state predpojačalom i modulom klase "D". U gornjem redu, nalazi se sekcija koja je osnova Vašeg tona. Poseduje Gain kontrolu i aktivni 4-pojasni EK: zajedno sa Lov i Treble kontrolama, Lov Mids i Hi Mids kontrole, svako dugme sa sopstvenim dvosmernim prekidačem. U donjem redu, nalazi se Microtubes Engine® , dodatni kanal koji će Vaš čist ton dovesti na jedan viši nivo. Uživajte !

Massive tone for the masses
The Microtubes® 500 is a 500W amplifier equipped with an all analog solid state preamplifier and a Class D Power Module. On the top row, you will find the clean section which is the foundation of your tone. It features a Gain control and an active 4 band EQ: along with Low and Treble controls, you will find Low Mids and Hi Mids controls, each knob with their own 2-way frequency switch.  

Front Panel Features:

Input
Connect your instrument via a standard 1” mono cable.

Passive/Active
Switch from passive to active mode. Some active basses can have a hotter signal output which can make the amplifier distort early (feel free to use it on Passive mode even with active basses if such additional distortion is desired).

Microtubes
Engages the Microtubes Engine™ to add natural compression, organic harmonic enhancement, and saturation ranging from mild overdrive to high gain bass rage. The Microtubes Engine operates before the clean section (you can, therefore, use the 4 Band Active EQ for additional tone shaping in addition to the Tone knob described below)

Drive
Sets the Microtubes Engine’s distortion level. Ranging from soft, warm overdrive to devastating saturation plus everything in between.

Tone
Controls the high harmonic content of the Microtubes Engine via a variable low pass filter: crank it up for additional attack and definition or dim it down for a smoother sound. This is handy when running bright EQ settings or cabinets with tweeters.

Level
Controls the Microtubes Engine’s output volume.

Blend
Mixes between the Clean and Distortion signals (Microtubes Engine).

B3K/VMT
Selects between two overdrive circuits: B3K mode will deliver an aggressive, percussive sound while the VMT will bring up the mids for a warmer, more neutral character.

Gain
Changes the volume of the signal driving the Active 4 Band EQ. You can set it low for cleaner tone or set it higher for more aggressive growl.

Bass
+-12dB at 80Hz. Changes the low content of the signal.

Low Mids
+-12dB of the selected frequency via the LOW MIDS f switch (described below).

Treble
+-12dB at 5kHz. Changes the high content of the signal.

Master
Controls the overall volume of the amplifier. This control does not affect DI output or effects loop level.

Footswitch
The Footswitch jack allows you to remotely engage and disengage the Microtubes Engine via our Intelligent Footswitch (sold separately). Hold the footswitch to Mute the amplifier. The VMT/B3K push button will remain operational with the Intelligent Footswitch plugged in.   * Use a regular mono instrument cable to connect the amplifier to the footswitch. * Remove the cable from the footswitch jack in the rear panel if you want to control the amp from the front panel.  

Back Panel Features:

Speaker Output
Connects the amplifier to your cabinet. This Speakon combo jack allows for either Speakon or 1” speaker cable operation. The minimum load for the amplifier is 4? . For higher impedance loads the maximum output power is reduced. The Microtubes 500 amplifier can run without a cabinet connected to this output. WARNING: Do not use an instrument cable with this jack. Using an instrument cable can damage your amplifier. Do not use a load lower than 4.

Headphone Output
Headphones with 1/4” plug connector can be connected to this jack. For quiet operation remove any speaker cabinet connected to the amplifier, as connecting the headphones does not disable the speaker output.  

Send
Line level effects loop output. Connect a cable from this jack to the input of any pedals used in the effects loop. The output can be used to connect to another power amplifier or a sound card. The output is not controlled by the Master volume. Gain control can be used to change the signal.

Return
Line level effects loop input. Connect the output from your effects loop pedals to this connector.

Post-Pre
Selects which signal will be sent to the Balanced output. Selecting PRE, sends a clean copy of your input bass signal. Selecting POST delivers the processed signal by the preamplifier (Microtubes Engine, gain, eq. )

DIMENSIONS
23.2x19x7.3 mm (9.13x7.48x2.87 in)



Kontakt:

● AudioPro ARTIST Sistems d. o. o. ●

BEOGRAD
Bulevar Milutina Milankovića 98-100
Novi Beograd 
tel : 011/ 344-28-74

NOVI SAD
Maksima Gorkog 16
tel: 021/ 300-69-11

NE PRIHVATAMO ZAMENE!

ID Oglasa: #80465614
Informacije

NAŠA NOVA ADRESA  :

● AudioPro ARTIST Sistems d. o. o. ●
NOVI BEOGRAD
Bulevar Milutina Milankovića 98
tel : 011/ 344-28-74

 

NE PRIHVATAMO ZAMENE!

 

> > > > > > RADNJA U NOVOM SADU JE ZATVORENA < < < < < <

 

napomena :

Zbog čestih promena cena proizvođača, cene na KP su informativnog karaktera.
Aktuelne cene možete videti na našem zvaničnom sajtu 

Hvala na razumevanju.

 

PredlogProblemKontakt

U skladu sa Pravilima i uslovima korišćenja i Polisom o poštovanju privatnosti, KupujemProdajem koristi Cookie-je da bi obezbedio dobro korisničko iskustvo, prikazivanje personalizovanog sadržaja, prikazivanje reklama, kao i druge funkcionalnosti i usluge koje ne bismo mogli da obezbedimo bez Cookie-ja.