Raspberry Pi Expansion board Debug Probe

EAN: 5056561803265

Raspberry Pi® debug probe

The Raspberry Pi Debug Probe is an inexpensive, all-in-one USB-to-debug kit that provides all the necessary hardware and cables for easy, solderless, plug-and-play debugging – perfect for debugging a Raspberry Pi Pico and other boards!

It is designed to make it easy to debug and program a Pico and RP2040 with a range of host platforms including Windows, Mac, and typical Linux computers.

The Debug Probe provides both a processor serial debug interface (ARM Serial Wire Debug interface by default, other interfaces can be supported) and an industry-standard UART interface. It’s based on the Raspberry Pi Pico hardware design and runs the open-source Raspberry Pi Picoprobe software.

Updating the firmware is accomplished in the same way as on a Raspberry Pi Pico, so it is straightforward to keep the unit up to date with the latest Picoprobe firmware or to use custom firmware.

The Debug Probe comes with a compact clear case, three JST-SH debug cables and a Micro-USB cable. The 3-pin JST-SH connectors match those used on the Raspberry Pi Pico H, providing a quick and easy way to debug your Pico project.

Whilst it has been designed primarily for use with Raspberry Pi debug targets, the Debug Probe provides standard CMSIS-DAP debug and UART interfaces over USB, so it can be used to debug other targets and development boards, or simply as a cost-effective USB-to-UART cable.  It works with OpenOCD and other tools that support
CMSIS-DAP.

Features

• RP2040-based Debug Probe
• All-in-one USB to serial + UART bridge
• USB to two-wire serial debug bridge (Arm Serial Wire Debug supported by default)
• Compatible with the CMSIS-DAP standard
• Follows the Raspberry Pi 3-pin Debug Connector Specification
• Runs Picoprobe software
• Easily updated, or use custom firmware
• Includes everything you need
• Standard CMSIS-DAP debug and UART interfaces over USB (not just for Pico debugging! )
• Works with OpenOCD and other tools supporting CMSIS-DAP

Specifications

• Form factor: 22mm × 32mm
• Nominal I/O voltage: 3.3V
• Operating temperature: -20° C to +70° C
• Production lifetime: The Raspberry Pi Debug Probe will remain in production until at least January 2028
• Compliance: For a full list of local and regional product approvals, please visit pip. raspberrypi. com

Package Contents

• 1x Raspberry Pi Debug Probe (board)
• 1x Debug Probe Case (clear)
• 1x Micro-USB cable
• 1x JST-SH 3-pin cable set, including:

• 1x JST-SH 3-pin to JST-SH 3-pin
• 1x JST-SH 3-pin to male jumper
• 1x JST-SH 3-pin to female header

R0113

ꕥꕥꕥꕥꕥꕥꕥꕥꕥꕥꕥꕥꕥꕥꕥꕥꕥꕥꕥꕥꕥꕥꕥꕥꕥꕥꕥꕥꕥꕥꕥꕥꕥꕥꕥꕥ

  Račun.
  Garancija.
  Zagarantovana sva prava kupaca po osnovu zakona o zaštiti potrošača.
  

  Malina314 doo

ꕥꕥꕥꕥꕥꕥꕥꕥꕥꕥꕥꕥꕥꕥꕥꕥꕥꕥꕥꕥꕥꕥꕥꕥꕥꕥꕥꕥꕥꕥꕥꕥꕥꕥꕥꕥ

Slanje sa kurirskim službama.

Plaćanje pre slanja ili pouzećem.

Malina314 doo
Pogledajte i naše druge oglase.

Volimo da prodajemo.