Uređaj radi na 12V i isporučuje se u kućištu kao sa slike.
Maksimalne struje i naponi koje podnose releji: DC 0-30V / 10A, AC 0-250V / 10A
NC port maximum load capacity: DC 0-28V / 10A, AC 0-125V / 10A
Description:
Voltage: DC 12V
Current: 20A
Power: < 1800w
Shell Color: White/Blacl
LED Display Color: Red+Green/Red+Blue
Timing Range: 0-999s,0-999min,0-999h
Dimension: Display board 48x29mm;
Installation 45.5x26mm
Function Setting:18 kinds combination function
Features:
1. Double LED Display: can set two sets timing time. Timing time T1, timing time T2
2. Three Timing Time Chosen:0-999s,0-999min,0-999h
3. Six Operating Mode Setting
0. mode: after delay T1 time, relay will operate(T1 timing)
1. mode: after delay T1 time, relay will not operate(T1 timing)
2. mode: after delay T1 time, relay will operate(T1 timing); after delay T2 time, relay will not operate(T2 timing), end
3. mode: after delay T1 time, relay will not operate(T1 timing); after delay T2 time, relay wil operate(T2 timing), end
4. mode: after delay T1 time, relay will operate(T1 timing); after delay T2 time, relay wil not operate(T2 timing), repeat cycling
5. mode: after delay T1 time, relay will not operate(T1 timing); after delay T2 time, relay wil operate(T2 timing), repeat cycling
Product Instructions:
Please pay attention for your first use. You need wait 6s after your setting data, the module will save the date you have set after 6s.
Short press button SET: If you start the time setting mode , Nixie tube will blink. You could adjust the time T1 and T2 by button+ and button-. Please wait 5s after your setting date, the module will save the date you have set after 5s .
Long press button SET: if you start the parameter setting mode. There are two group parameter for your choice : P0 and P1. You could switch P0 or P1 by short press SET. Under the parameter P0 and P1, you could set the timing mode by the button+ and button-.
P0--0: Timing time mode : 0---999s.
P0--1: Timing time mode : 0---999min.
P0--2: Timing time mode : 0---999h.
P1--0: The relay will connect after you delay the T1 time .
P1--1: The relay will disconnect after you delay the T1 time.
P1--2: The relay will connect after you delay the T1 time first, Then the relay will disconnect after you delay the T2 time , it finish.
P1--3: The relay will disconnect after you delay the T1 time first, Then the relay will connect after you delay the T2 time , it finish.
P1--4: The relay will connect after you delay the T1 time first, Then the relay will disconnect after you delay the T2 time , it is cyclic.
P1--5: The relay will disconnect after you delay the T1 time first, Then the relay will connect after you delay the T2 time , it cyclic.
Example: A customer needs 10 seconds to start up and 20 seconds off. Setup is as follows:
T1 set time 10, T2 set time 20
P0 -- 0 (T1 time range is seconds)
P1--5 (timer work mode)
Package Included:
1 x Dual Display Time Delay Relay
U skladu sa Pravilima i uslovima korišćenja i Polisom o poštovanju privatnosti, KupujemProdajem koristi Cookie-je da bi obezbedio dobro korisničko iskustvo, prikazivanje personalizovanog sadržaja, prikazivanje reklama, kao i druge funkcionalnosti i usluge koje ne bismo mogli da obezbedimo bez Cookie-ja.